FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W1554927377> ?p ?o ?g. }

• W1554927377 abstract "The stencil printing process is an important process in the assembly of Surface Mount Technology (SMT)devices. There is a wide agreement in the industry that the paste printing process accounts for the majority of assembly defects. Experience with this process has shown that typically over 60% of all soldering defects are due to problems associated with the flow properties of solder pastes. Therefore, the rheological measurements can be used as a tool to study the deformation or flow experienced by the pastes during the stencil printing process. This paper presents results on the thixotropic behaviour of three pastes; lead-based solder paste, lead-free solder paste and isotropic conductive adhesive (ICA). These materials are widely used as interconnect medium in the electronics industry. Solder paste are metal alloys suspended in a flux medium while the ICAs consist of silver flakes dispersed in an epoxy resin. The thixotropy behaviour was investigated through two rheological test; (i) hysteresis loop test and (ii) steady shear rate test. In the hysteresis loop test, the shear rate were increased from 0.001 to 100s-1 and then decreased from 100 to 0.001s-1. Meanwhile, in the steady shear rate test, the materials were subjected to a constant shear rate of 0.100, 100 and 0.001s-1 for a period of 240 seconds. All the pastes showed a high degree of shear thinning behaviour with time. This might be due to the agglomeration of particles in the flux or epoxy resin that prohibits pastes flow under low shear rate. The action of high shear rate would break the agglomerates into smaller pieces which facilitates the flow of pastes, thus viscosity is reduced at high shear rate. The solder pastes exhibited a higher degree of structural breakdown compared to the ICAs. The area between the up curve and down curve in the hysteresis curve is an indication of the thixotropic behavior of the pastes. Among the three pastes, lead-free solder paste showed the largest area between the down curve and up curve, which indicating a larger structural breakdown in the pastes, followed by lead-based solder paste and ICA. In a steady shear rate test, viscosity of ICA showed the best recovery with the steeper curve to its original viscosity after the removal of shear, which indicating that the dispersion quality in ICA is good because the high shear has little effect on the microstructure of ICA. In contrast, lead-based paste showed the poorest recovery which means this paste undergo larger structural breakdown and dispersion quality in this paste is poor because the microstructure of the paste is easily disrupted by high shear. The structural breakdown during the application of shear and the recovery after removal of shear is an important characteristic in the paste printing process. If the paste’s viscosity can drop low enough, it may contribute to the aperture filling and quick recovery may prevent slumping." @default.
• W1554927377 created "2016-06-24" @default.
• W1554927377 creator A5027328321 @default.
• W1554927377 creator A5059932324 @default.
• W1554927377 creator A5072349272 @default.
• W1554927377 creator A5073710450 @default.
• W1554927377 date "2009-12-03" @default.
• W1554927377 modified "2023-09-27" @default.
• W1554927377 title "Thixotropic studies of lead-based solder, lead-free solder and conductive adhesive pastes" @default.
• W1554927377 hasPublicationYear "2009" @default.
• W1554927377 type Work @default.
• W1554927377 sameAs 1554927377 @default.
• W1554927377 citedByCount "0" @default.
• W1554927377 crossrefType "journal-article" @default.
• W1554927377 hasAuthorship W1554927377A5027328321 @default.
• W1554927377 hasAuthorship W1554927377A5059932324 @default.
• W1554927377 hasAuthorship W1554927377A5072349272 @default.
• W1554927377 hasAuthorship W1554927377A5073710450 @default.
• W1554927377 hasConcept C159985019 @default.
• W1554927377 hasConcept C165682214 @default.
• W1554927377 hasConcept C191281628 @default.
• W1554927377 hasConcept C191897082 @default.
• W1554927377 hasConcept C192562407 @default.
• W1554927377 hasConcept C200990466 @default.
• W1554927377 hasConcept C202374169 @default.
• W1554927377 hasConcept C2776584680 @default.
• W1554927377 hasConcept C2779227376 @default.
• W1554927377 hasConcept C41151612 @default.
• W1554927377 hasConcept C50296614 @default.
• W1554927377 hasConcept C56918372 @default.
• W1554927377 hasConcept C68928338 @default.
• W1554927377 hasConcept C96035792 @default.
• W1554927377 hasConceptScore W1554927377C159985019 @default.
• W1554927377 hasConceptScore W1554927377C165682214 @default.
• W1554927377 hasConceptScore W1554927377C191281628 @default.
• W1554927377 hasConceptScore W1554927377C191897082 @default.
• W1554927377 hasConceptScore W1554927377C192562407 @default.
• W1554927377 hasConceptScore W1554927377C200990466 @default.
• W1554927377 hasConceptScore W1554927377C202374169 @default.
• W1554927377 hasConceptScore W1554927377C2776584680 @default.
• W1554927377 hasConceptScore W1554927377C2779227376 @default.
• W1554927377 hasConceptScore W1554927377C41151612 @default.
• W1554927377 hasConceptScore W1554927377C50296614 @default.
• W1554927377 hasConceptScore W1554927377C56918372 @default.
• W1554927377 hasConceptScore W1554927377C68928338 @default.
• W1554927377 hasConceptScore W1554927377C96035792 @default.
• W1554927377 hasLocation W15549273771 @default.
• W1554927377 hasOpenAccess W1554927377 @default.
• W1554927377 hasPrimaryLocation W15549273771 @default.
• W1554927377 hasRelatedWork W1986489716 @default.
• W1554927377 hasRelatedWork W2002526565 @default.
• W1554927377 hasRelatedWork W2010158632 @default.
• W1554927377 hasRelatedWork W2018281886 @default.
• W1554927377 hasRelatedWork W2028641901 @default.
• W1554927377 hasRelatedWork W2059513600 @default.
• W1554927377 hasRelatedWork W2117000433 @default.
• W1554927377 hasRelatedWork W2118568828 @default.
• W1554927377 hasRelatedWork W2118899737 @default.
• W1554927377 hasRelatedWork W2146083090 @default.
• W1554927377 hasRelatedWork W2156250146 @default.
• W1554927377 hasRelatedWork W2170560481 @default.
• W1554927377 hasRelatedWork W2278814454 @default.
• W1554927377 hasRelatedWork W2354601899 @default.
• W1554927377 hasRelatedWork W2375534531 @default.
• W1554927377 hasRelatedWork W2559237731 @default.
• W1554927377 hasRelatedWork W2981587926 @default.
• W1554927377 hasRelatedWork W607063581 @default.
• W1554927377 hasRelatedWork W852863952 @default.
• W1554927377 hasRelatedWork W2910049811 @default.
• W1554927377 isParatext "false" @default.
• W1554927377 isRetracted "false" @default.
• W1554927377 magId "1554927377" @default.
• W1554927377 workType "article" @default.