Matches in SemOpenAlex for { <https://semopenalex.org/work/W1593230145> ?p ?o ?g. }
Showing items 1 to 77 of
77
with 100 items per page.
- W1593230145 abstract "Damage tolerance testing development was required to help qualify a new spin forming dome fabrication process for the Ares 1 program at Marshall Space Flight Center (MSFC). One challenge of the testing was due to the compound curvature of the dome. The testing was developed on a sub-scale dome with a diameter of approximately 40 inches. The simulated service testing performed was based on the EQTP1102 Rev L 2195 Aluminum Lot Acceptance Simulated Service Test and Analysis Procedure generated by Lockheed Martin for the Space Shuttle External Fuel Tank. This testing is performed on a specimen with an induced flaw of elliptical shape generated by Electrical Discharge Machining (EDM) and subsequent fatigue cycling for crack propagation to a predetermined length and depth. The specimen is then loaded in tension at a constant rate of displacement at room temperature until fracture occurs while recording load and strain. An identical specimen with a similar flaw is then proof tested at room temperature to imminent failure based on the critical offset strain achieved by the previous fracture test. If the specimen survives the proof, it is then subjected to cryogenic cycling with loads that are a percentage of the proof load performed at room temperature. If all cryogenic cycles are successful, the specimen is loaded in tension to failure at the end of the test. This standard was generated for flat plate, so a method of translating this to a specimen of compound curvature was required. This was accomplished by fabricating a fixture that maintained the curvature of the specimen rigidly with the exception of approximately one-half inch in the center of the specimen containing the induced flaw. This in conjunction with placing the center of the specimen in the center of the load train allowed for successful testing with a minimal amount of bending introduced into the system. Stress corrosion cracking (SCC) tests were performed using the typical double beam assembly and with 4-point loaded specimens under alternate immersion conditions in a 3.5% NaCl environment for 90 days. In addition, experiments were conducted to determine the threshold stress intensity factor for SCC (K1SCC) of Al-Li 2195 which to our knowledge has not been determined previously. The successful simulated service and stress corrosion testing helped to provide confidence to continue to Ares 1 scale dome fabrication." @default.
- W1593230145 created "2016-06-24" @default.
- W1593230145 creator A5001333825 @default.
- W1593230145 creator A5006276166 @default.
- W1593230145 creator A5063379777 @default.
- W1593230145 creator A5071283080 @default.
- W1593230145 date "2010-06-28" @default.
- W1593230145 modified "2023-09-26" @default.
- W1593230145 title "Simulated Service and Stress Corrosion Cracking Testing for Friction Stir Welded Spun Formed Domes" @default.
- W1593230145 hasPublicationYear "2010" @default.
- W1593230145 type Work @default.
- W1593230145 sameAs 1593230145 @default.
- W1593230145 citedByCount "0" @default.
- W1593230145 crossrefType "journal-article" @default.
- W1593230145 hasAuthorship W1593230145A5001333825 @default.
- W1593230145 hasAuthorship W1593230145A5006276166 @default.
- W1593230145 hasAuthorship W1593230145A5063379777 @default.
- W1593230145 hasAuthorship W1593230145A5071283080 @default.
- W1593230145 hasConcept C127413603 @default.
- W1593230145 hasConcept C159985019 @default.
- W1593230145 hasConcept C180016635 @default.
- W1593230145 hasConcept C186068551 @default.
- W1593230145 hasConcept C191897082 @default.
- W1593230145 hasConcept C192562407 @default.
- W1593230145 hasConcept C19474535 @default.
- W1593230145 hasConcept C195065555 @default.
- W1593230145 hasConcept C2524010 @default.
- W1593230145 hasConcept C2778502540 @default.
- W1593230145 hasConcept C2781122048 @default.
- W1593230145 hasConcept C33923547 @default.
- W1593230145 hasConcept C60584519 @default.
- W1593230145 hasConcept C66938386 @default.
- W1593230145 hasConcept C77595967 @default.
- W1593230145 hasConcept C78519656 @default.
- W1593230145 hasConceptScore W1593230145C127413603 @default.
- W1593230145 hasConceptScore W1593230145C159985019 @default.
- W1593230145 hasConceptScore W1593230145C180016635 @default.
- W1593230145 hasConceptScore W1593230145C186068551 @default.
- W1593230145 hasConceptScore W1593230145C191897082 @default.
- W1593230145 hasConceptScore W1593230145C192562407 @default.
- W1593230145 hasConceptScore W1593230145C19474535 @default.
- W1593230145 hasConceptScore W1593230145C195065555 @default.
- W1593230145 hasConceptScore W1593230145C2524010 @default.
- W1593230145 hasConceptScore W1593230145C2778502540 @default.
- W1593230145 hasConceptScore W1593230145C2781122048 @default.
- W1593230145 hasConceptScore W1593230145C33923547 @default.
- W1593230145 hasConceptScore W1593230145C60584519 @default.
- W1593230145 hasConceptScore W1593230145C66938386 @default.
- W1593230145 hasConceptScore W1593230145C77595967 @default.
- W1593230145 hasConceptScore W1593230145C78519656 @default.
- W1593230145 hasLocation W15932301451 @default.
- W1593230145 hasOpenAccess W1593230145 @default.
- W1593230145 hasPrimaryLocation W15932301451 @default.
- W1593230145 hasRelatedWork W102018325 @default.
- W1593230145 hasRelatedWork W111770725 @default.
- W1593230145 hasRelatedWork W1489921544 @default.
- W1593230145 hasRelatedWork W1571433608 @default.
- W1593230145 hasRelatedWork W1997566311 @default.
- W1593230145 hasRelatedWork W2061146014 @default.
- W1593230145 hasRelatedWork W2171712425 @default.
- W1593230145 hasRelatedWork W2521444833 @default.
- W1593230145 hasRelatedWork W3014148518 @default.
- W1593230145 hasRelatedWork W3026513551 @default.
- W1593230145 hasRelatedWork W3095496565 @default.
- W1593230145 hasRelatedWork W312318778 @default.
- W1593230145 hasRelatedWork W330020635 @default.
- W1593230145 hasRelatedWork W351437998 @default.
- W1593230145 hasRelatedWork W770815034 @default.
- W1593230145 hasRelatedWork W838194965 @default.
- W1593230145 hasRelatedWork W2513018296 @default.
- W1593230145 hasRelatedWork W2840952074 @default.
- W1593230145 hasRelatedWork W2933212424 @default.
- W1593230145 hasRelatedWork W598355678 @default.
- W1593230145 isParatext "false" @default.
- W1593230145 isRetracted "false" @default.
- W1593230145 magId "1593230145" @default.
- W1593230145 workType "article" @default.