FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W2003513013> ?p ?o ?g. }

• W2003513013 abstract "Abstract Sponge coring is a relatively cheap, direct, method to measure local oil saturations. Although the basic concept is simple - oil which flows from the core is collected in the enclosing sponge material- the actual flow processes which take place are complicated, and have not been fully analyzed to date. In this paper, we develop a practical model of the sponge coring process, which is ideally suited for engineering purposes. The model combines the spontaneous imbibition process with the simultaneous movement of the sponge relative to the core. All parameters are combined in dimensionless scaling groups, which make it possible to quickly estimate the resulting oil distribution in the sponge given the characteristic field conditions. More importantly, the initial oil distribution in the core can be calculated by solving the inverse problem. In addition, we report the results of a laboratory study, in which we measured the water-oil capillary pressure curve of the sponge, and residual oil saturation in the presence of both water and gas. Introduction Sponge coring was developed between 1977 and 1980, and is commercially available since 1981. The objective of sponge coring is to measure the interstitial oil saturation directly. Sponge coring therefore is an alternative to pressure coring which is more costly, complicated and time consuming. Sponge coring is most widely applied to measure the remaining oil saturation. The basic concept of sponge coring is simple. Oil which leaks from the core during the coring process is collected in the enclosing sponge material. However, the actual flow processes which take place are complicated, and have not been thoroughly analyzed to date. In this work, we model part of the flow processes which are important during sponge coring; the capillary driven exchange of fluids between the core and the sponge. Although this flow is in the horizontal direction, it may also cause vertical redistribution of the oil due to the simultaneous movement of the sponge relative to the core. We model the theoretical oil distribution which is caused by this process. Sponge Coring Procedure The sponge coring technique uses a sponge-sleeve modification to a conventional core barrel. Figure 1 shows a schematic picture of the sponge inside the aluminum liner. Prior to the coring operation, the sponge is saturated with water with the reservoir connate water properties. As the core is being drilled, the sponge liner is designed to fit tightly around the core. Oil which leaks from the core during coring and core retrieval is thus collected in the sponge material. After retrieval, the core is cut into slabs, which are analyzed for their oil content. The amount of oil in the core and the sponge is converted back to reservoir conditions by use of the formation volume factor. Sponge Properties. The sponge sleeve is made of polyurethane material, with a porosity higher than 80 % and a reported air permeability in the order of 2 Darcy The sponge material was verified to be chemically inert and stable under most coring conditions. Capillary pressure curve. In this study, we have measured the capillary pressure curve for a sponge material sample, which we found to be water-wet. The drainage curve, shown in Fig. 2, was measured using double distilled water and decane, with an interfacial tension of 0.028 N/m. Three Phase Residual Oil Saturation. Three phase residual oil saturations can vary significantly from the 2-phase values due to spreading of the oil phase on the water-gas interface. P. 435^" @default.
• W2003513013 created "2016-06-24" @default.
• W2003513013 creator A5011852572 @default.
• W2003513013 creator A5031329843 @default.
• W2003513013 creator A5045727757 @default.
• W2003513013 creator A5059476455 @default.
• W2003513013 creator A5083076122 @default.
• W2003513013 date "1997-10-05" @default.
• W2003513013 modified "2023-09-27" @default.
• W2003513013 title "Analysis and Modeling of Flow Processes During Sponge Coring" @default.
• W2003513013 doi "https://doi.org/10.2118/38690-ms" @default.
• W2003513013 hasPublicationYear "1997" @default.
• W2003513013 type Work @default.
• W2003513013 sameAs 2003513013 @default.
• W2003513013 citedByCount "2" @default.
• W2003513013 countsByYear W20035130132014 @default.
• W2003513013 countsByYear W20035130132018 @default.
• W2003513013 crossrefType "proceedings-article" @default.
• W2003513013 hasAuthorship W2003513013A5011852572 @default.
• W2003513013 hasAuthorship W2003513013A5031329843 @default.
• W2003513013 hasAuthorship W2003513013A5045727757 @default.
• W2003513013 hasAuthorship W2003513013A5059476455 @default.
• W2003513013 hasAuthorship W2003513013A5083076122 @default.
• W2003513013 hasConcept C112213829 @default.
• W2003513013 hasConcept C114614502 @default.
• W2003513013 hasConcept C127313418 @default.
• W2003513013 hasConcept C127413603 @default.
• W2003513013 hasConcept C151730666 @default.
• W2003513013 hasConcept C159985019 @default.
• W2003513013 hasConcept C192562407 @default.
• W2003513013 hasConcept C2164484 @default.
• W2003513013 hasConcept C25197100 @default.
• W2003513013 hasConcept C2778849931 @default.
• W2003513013 hasConcept C33923547 @default.
• W2003513013 hasConcept C6385141 @default.
• W2003513013 hasConcept C78519656 @default.
• W2003513013 hasConcept C78762247 @default.
• W2003513013 hasConcept C9930424 @default.
• W2003513013 hasConceptScore W2003513013C112213829 @default.
• W2003513013 hasConceptScore W2003513013C114614502 @default.
• W2003513013 hasConceptScore W2003513013C127313418 @default.
• W2003513013 hasConceptScore W2003513013C127413603 @default.
• W2003513013 hasConceptScore W2003513013C151730666 @default.
• W2003513013 hasConceptScore W2003513013C159985019 @default.
• W2003513013 hasConceptScore W2003513013C192562407 @default.
• W2003513013 hasConceptScore W2003513013C2164484 @default.
• W2003513013 hasConceptScore W2003513013C25197100 @default.
• W2003513013 hasConceptScore W2003513013C2778849931 @default.
• W2003513013 hasConceptScore W2003513013C33923547 @default.
• W2003513013 hasConceptScore W2003513013C6385141 @default.
• W2003513013 hasConceptScore W2003513013C78519656 @default.
• W2003513013 hasConceptScore W2003513013C78762247 @default.
• W2003513013 hasConceptScore W2003513013C9930424 @default.
• W2003513013 hasLocation W20035130131 @default.
• W2003513013 hasOpenAccess W2003513013 @default.
• W2003513013 hasPrimaryLocation W20035130131 @default.
• W2003513013 hasRelatedWork W2000601557 @default.
• W2003513013 hasRelatedWork W2057011307 @default.
• W2003513013 hasRelatedWork W2066574688 @default.
• W2003513013 hasRelatedWork W2334598720 @default.
• W2003513013 hasRelatedWork W2349189045 @default.
• W2003513013 hasRelatedWork W2361497670 @default.
• W2003513013 hasRelatedWork W2374232993 @default.
• W2003513013 hasRelatedWork W2381138702 @default.
• W2003513013 hasRelatedWork W30259257 @default.
• W2003513013 hasRelatedWork W59040450 @default.
• W2003513013 isParatext "false" @default.
• W2003513013 isRetracted "false" @default.
• W2003513013 magId "2003513013" @default.
• W2003513013 workType "article" @default.