FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W2028404677> ?p ?o ?g. }

• W2028404677 endingPage "616" @default.
• W2028404677 startingPage "606" @default.
• W2028404677 abstract "In the secondary recovery process used in this field, water was injected into combustion zones during active burning and after air injection had ceased. Combustion and steam stimulation treatments were also used at producing wells to improve sweep efficiency and production rates. Results indicated that higher crude oil prices are needed to make thermal recovery processes economic at Tisdale. Introduction The forward in-situ combustion process was the most important of several thermal methods applied at North Tisdale field, north central Wyoming. Operationally, a foward combustion process is basically a gas injection project. Air is usually injected at compressor capacity or at maximum permissible pressures. Combustion zones are permissible pressures. Combustion zones are established near the injection wells and propagated through the formation by continued injection of air, thus forcing formation fluids toward producing wells. The process is far from being clearly understood. However, consider-considerable progress has been made toward demonstrating its technical and practical feasibility . Continental Oil Co. tested air injectivity at North Tisdale field in 1957 and performed the first fireflood ignition in Wyoming in May, 1959. Envisioned in the pilot test was a basic two-step process in which first pilot test was a basic two-step process in which first air would be injected, then water would be injected into the burned zones to create an in-situ hot waterflood and steam drive. This would utilize the residual heat behind the combustion front and improve the economics of oil displacement. Other modifications to the basic process, such as simultaneous or cyclic injection of air and water, were also envisioned in the original proposal. These methods were developed as the project proceeded. Combustion and steam stimulation treatments were also used at producing wells during the project. The Reservoir The Curtis sand reservoir was discovered in June, 1952. Development continued during 1953 and 1954 on a 10-acre pattern that was somewhat irregular because of the rough terrain. Figs. 1 and 2 show the well locations. After 5 1/2-in. J-55 STC casing was set on top of the sand, the wells were completed by drilling 20 to 40 ft into the pay with cable tools and shooting with nitroglycerin. The reservoir lies on top of a sightly arched and tilted water table that dips about 3 degrees to the north. Sand depth varies from 776 to 1,090 ft in the productive area. Gross sand thickness is about 100 ft, productive area. Gross sand thickness is about 100 ft, and average net effective pay in the developed area is about 50 ft. The original oil content was about 15 million bbl or 1,230 bbl/acre-ft. The Curtis sand is a member of the Crow Mountain formation of the Triassic period. It is a porous, occasionally friable, orange-and-white sandstone with a field average permeability of 1,034 md, a porosity of 24.5 percent, and initial saturations of 64.6 percent oil and 35.4 percent water. The sour crude oil has a gravity of 21 degrees API and a viscosity of 175 cp at the original reservoir conditions of 290 psig and 73 degrees F. Why Thermal Recovery Was Selected Water cuts had increased to 50 percent by the time the original development was completed. The primary producing rate had declined from a peak of primary producing rate had declined from a peak of 312 BOPD to 180 BOPD by 1957, and it was estimated that less than 5.0 percent of the oil in place would be recovered economically. JPT P. 606" @default.
• W2028404677 created "2016-06-24" @default.
• W2028404677 creator A5025757491 @default.
• W2028404677 creator A5057995839 @default.
• W2028404677 creator A5076413757 @default.
• W2028404677 creator A5088566317 @default.
• W2028404677 date "1972-05-01" @default.
• W2028404677 modified "2023-09-25" @default.
• W2028404677 title "Thermal Recovery at North Tisdale Field, Wyoming" @default.
• W2028404677 doi "https://doi.org/10.2118/3595-pa" @default.
• W2028404677 hasPublicationYear "1972" @default.
• W2028404677 type Work @default.
• W2028404677 sameAs 2028404677 @default.
• W2028404677 citedByCount "3" @default.
• W2028404677 countsByYear W20284046772015 @default.
• W2028404677 crossrefType "journal-article" @default.
• W2028404677 hasAuthorship W2028404677A5025757491 @default.
• W2028404677 hasAuthorship W2028404677A5057995839 @default.
• W2028404677 hasAuthorship W2028404677A5076413757 @default.
• W2028404677 hasAuthorship W2028404677A5088566317 @default.
• W2028404677 hasConcept C105923489 @default.
• W2028404677 hasConcept C111919701 @default.
• W2028404677 hasConcept C127313418 @default.
• W2028404677 hasConcept C127413603 @default.
• W2028404677 hasConcept C151730666 @default.
• W2028404677 hasConcept C152984320 @default.
• W2028404677 hasConcept C175234220 @default.
• W2028404677 hasConcept C17623918 @default.
• W2028404677 hasConcept C178790620 @default.
• W2028404677 hasConcept C183250156 @default.
• W2028404677 hasConcept C185592680 @default.
• W2028404677 hasConcept C2776124570 @default.
• W2028404677 hasConcept C2778059233 @default.
• W2028404677 hasConcept C2779681308 @default.
• W2028404677 hasConcept C39432304 @default.
• W2028404677 hasConcept C41008148 @default.
• W2028404677 hasConcept C548081761 @default.
• W2028404677 hasConcept C548895740 @default.
• W2028404677 hasConcept C57054060 @default.
• W2028404677 hasConcept C68189081 @default.
• W2028404677 hasConcept C78762247 @default.
• W2028404677 hasConcept C81803558 @default.
• W2028404677 hasConcept C98045186 @default.
• W2028404677 hasConceptScore W2028404677C105923489 @default.
• W2028404677 hasConceptScore W2028404677C111919701 @default.
• W2028404677 hasConceptScore W2028404677C127313418 @default.
• W2028404677 hasConceptScore W2028404677C127413603 @default.
• W2028404677 hasConceptScore W2028404677C151730666 @default.
• W2028404677 hasConceptScore W2028404677C152984320 @default.
• W2028404677 hasConceptScore W2028404677C175234220 @default.
• W2028404677 hasConceptScore W2028404677C17623918 @default.
• W2028404677 hasConceptScore W2028404677C178790620 @default.
• W2028404677 hasConceptScore W2028404677C183250156 @default.
• W2028404677 hasConceptScore W2028404677C185592680 @default.
• W2028404677 hasConceptScore W2028404677C2776124570 @default.
• W2028404677 hasConceptScore W2028404677C2778059233 @default.
• W2028404677 hasConceptScore W2028404677C2779681308 @default.
• W2028404677 hasConceptScore W2028404677C39432304 @default.
• W2028404677 hasConceptScore W2028404677C41008148 @default.
• W2028404677 hasConceptScore W2028404677C548081761 @default.
• W2028404677 hasConceptScore W2028404677C548895740 @default.
• W2028404677 hasConceptScore W2028404677C57054060 @default.
• W2028404677 hasConceptScore W2028404677C68189081 @default.
• W2028404677 hasConceptScore W2028404677C78762247 @default.
• W2028404677 hasConceptScore W2028404677C81803558 @default.
• W2028404677 hasConceptScore W2028404677C98045186 @default.
• W2028404677 hasIssue "05" @default.
• W2028404677 hasLocation W20284046771 @default.
• W2028404677 hasOpenAccess W2028404677 @default.
• W2028404677 hasPrimaryLocation W20284046771 @default.
• W2028404677 hasRelatedWork W1971819457 @default.
• W2028404677 hasRelatedWork W1991410711 @default.
• W2028404677 hasRelatedWork W1992492699 @default.
• W2028404677 hasRelatedWork W1997582333 @default.
• W2028404677 hasRelatedWork W2028404677 @default.
• W2028404677 hasRelatedWork W2029109926 @default.
• W2028404677 hasRelatedWork W2034818729 @default.
• W2028404677 hasRelatedWork W2042527934 @default.
• W2028404677 hasRelatedWork W2300211331 @default.
• W2028404677 hasRelatedWork W2302409430 @default.
• W2028404677 hasVolume "24" @default.
• W2028404677 isParatext "false" @default.
• W2028404677 isRetracted "false" @default.
• W2028404677 magId "2028404677" @default.
• W2028404677 workType "article" @default.