FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W2073160553> ?p ?o ?g. }

• W2073160553 endingPage "567" @default.
• W2073160553 startingPage "563" @default.
• W2073160553 abstract "Dry machining is an eco-friendly machining process and its importance in the manufacturing industries should be taken seriously. Machining without the use of any cutting fluid is becoming increasingly more popular due to concerns regarding the safety of the environment and reducing cost. Dry and wet turning of T6061 aluminium alloy was performed on a lathe by using Silicon Nitride (Si3N4) inserts as the cutting tool. Tool wear behaviour of Si3N4 cutting tool were studied with the aim of finding the optimum cutting conditions for both dry and wet machining. Machining was performed at four different cutting speeds; 292, 388, 518 and 689 m/min using two different cutting parameters (feed rate, f = 0.2 mm/rev, depth of cut, d = 0.1 mm and f = 0.4 mm/rev, d = 0.2 mm). Material removal rate (MRR) was also obtained and the temperature at the tool-chip interface were measured using an infrared (IR) thermometer as to see the effect of temperature rise during machining. Dry machining with smaller cutting parameters resulted in lower wear rates by 37 to 48% for all four cutting speeds. Nevertheless, reduction of wear rate by 38 to 57% was found from wet machining. The optimum cutting speed for both dry and wet machining of T6061 aluminium alloy using Si3N4 cutting tool was found to be 518 m/min for both cutting parameters. However, the optimum cutting parameters are apparently with the feed rate of 0.4 mm/rev and depth of cut of 0.2 mm. At the optimum cutting speed, the tool tip temperature for dry machining was higher than wet machining by 40 and 51% for f = 0.2 mm/rev and f = 0.4 mm/rev respectively. Dry machining of T6061 Aluminium alloy can be more suitable particularly at higher cutting speed with interrupted cutting operations." @default.
• W2073160553 created "2016-06-24" @default.
• W2073160553 creator A5000339620 @default.
• W2073160553 creator A5009085380 @default.
• W2073160553 creator A5078371808 @default.
• W2073160553 date "2012-12-01" @default.
• W2073160553 modified "2023-09-26" @default.
• W2073160553 title "Wear Analysis of Silicon Nitride (Si₃N₄) Cutting Tool in Dry Machining of T6061 Aluminium Alloy" @default.
• W2073160553 cites W1965308830 @default.
• W2073160553 cites W1981726697 @default.
• W2073160553 cites W2064502720 @default.
• W2073160553 doi "https://doi.org/10.4028/www.scientific.net/amm.268-270.563" @default.
• W2073160553 hasPublicationYear "2012" @default.
• W2073160553 type Work @default.
• W2073160553 sameAs 2073160553 @default.
• W2073160553 citedByCount "8" @default.
• W2073160553 countsByYear W20731605532013 @default.
• W2073160553 countsByYear W20731605532014 @default.
• W2073160553 countsByYear W20731605532016 @default.
• W2073160553 countsByYear W20731605532017 @default.
• W2073160553 countsByYear W20731605532020 @default.
• W2073160553 countsByYear W20731605532021 @default.
• W2073160553 countsByYear W20731605532022 @default.
• W2073160553 crossrefType "journal-article" @default.
• W2073160553 hasAuthorship W2073160553A5000339620 @default.
• W2073160553 hasAuthorship W2073160553A5009085380 @default.
• W2073160553 hasAuthorship W2073160553A5078371808 @default.
• W2073160553 hasConcept C191897082 @default.
• W2073160553 hasConcept C192562407 @default.
• W2073160553 hasConcept C2777431650 @default.
• W2073160553 hasConcept C2780026712 @default.
• W2073160553 hasConcept C2780383046 @default.
• W2073160553 hasConcept C513153333 @default.
• W2073160553 hasConcept C523214423 @default.
• W2073160553 hasConcept C544956773 @default.
• W2073160553 hasConceptScore W2073160553C191897082 @default.
• W2073160553 hasConceptScore W2073160553C192562407 @default.
• W2073160553 hasConceptScore W2073160553C2777431650 @default.
• W2073160553 hasConceptScore W2073160553C2780026712 @default.
• W2073160553 hasConceptScore W2073160553C2780383046 @default.
• W2073160553 hasConceptScore W2073160553C513153333 @default.
• W2073160553 hasConceptScore W2073160553C523214423 @default.
• W2073160553 hasConceptScore W2073160553C544956773 @default.
• W2073160553 hasLocation W20731605531 @default.
• W2073160553 hasOpenAccess W2073160553 @default.
• W2073160553 hasPrimaryLocation W20731605531 @default.
• W2073160553 hasRelatedWork W1991986159 @default.
• W2073160553 hasRelatedWork W2326348298 @default.
• W2073160553 hasRelatedWork W2373405944 @default.
• W2073160553 hasRelatedWork W2391049875 @default.
• W2073160553 hasRelatedWork W2392620835 @default.
• W2073160553 hasRelatedWork W2394414273 @default.
• W2073160553 hasRelatedWork W2580545854 @default.
• W2073160553 hasRelatedWork W2998757889 @default.
• W2073160553 hasRelatedWork W4250890523 @default.
• W2073160553 hasRelatedWork W4366748099 @default.
• W2073160553 hasVolume "268-270" @default.
• W2073160553 isParatext "false" @default.
• W2073160553 isRetracted "false" @default.
• W2073160553 magId "2073160553" @default.
• W2073160553 workType "article" @default.