Matches in SemOpenAlex for { <https://semopenalex.org/work/W2161871798> ?p ?o ?g. }
Showing items 1 to 72 of
72
with 100 items per page.
- W2161871798 abstract "Thermosetting polyester in a sheet molding compound (SMC) shrinks by 7 to 10% and causes fiber show-through and poor surface quality. Adding certain thermoplastics results in zero shrinkage and smooth surfaces ; these are called low-profile additives (LPA). Poly(vinyl acetate) (PVAc), a highly effective LPA, decreases the fracture energy from 66.3 to 35.1 J/m 2 when present as 14 wt% of the matrix, even though the PVAc is tough. It produces a nodular three dimensional network ; the crosslinked polyester nodules are interconnected by weak polyester bridges and the PVAc forms a thin coating on each nodule. The macroscopic crosslinking shrinkage is offset by void formation in the PVAc phase. Crack follows the void structure and cleaves the bridges between the nodules. Low matrix fracture toughness leads to high microcracking and early gross failure of the SMC. This paper presents alternative low profile additives that give excellent low profile effect with improved matrix fracture energy and SMC strength. Commercially available styrene-butadiene block copolymers were studied. These are less polar and form discrete cavitated domains of a few 100 μm in the solid polyester matrix. With this morphology, good low profile and toughening usually are contradictory, since the former requires small LPA particles for smooth surfaces and the latter requires large particles for crack bridging by the rubber. However, a good compromise was found in Epoxidized Kraton D1300X (a 50% diblock and 50% triblock copolymer of styrene and butadiene) with the compatibilizer Ricon 131MA17 (a maleic anhydride-polybutadiene adduct). This produces a low profile effect equivalent to PVAc, but with a higher matrix fracture energy of 70.7 J/m 2 and higher matrix modulus. With the epoxidized rubber, the flexural strength of the SMC increases by 13% over that with PVAc, with no sacrifice of the modulus or strain-to-failure." @default.
- W2161871798 created "2016-06-24" @default.
- W2161871798 creator A5003293901 @default.
- W2161871798 creator A5066980793 @default.
- W2161871798 date "1996-08-01" @default.
- W2161871798 modified "2023-09-24" @default.
- W2161871798 title "Tough low profile additives in sheet molding compound" @default.
- W2161871798 cites W2007771844 @default.
- W2161871798 cites W2066960217 @default.
- W2161871798 doi "https://doi.org/10.1002/pc.10644" @default.
- W2161871798 hasPublicationYear "1996" @default.
- W2161871798 type Work @default.
- W2161871798 sameAs 2161871798 @default.
- W2161871798 citedByCount "10" @default.
- W2161871798 crossrefType "journal-article" @default.
- W2161871798 hasAuthorship W2161871798A5003293901 @default.
- W2161871798 hasAuthorship W2161871798A5066980793 @default.
- W2161871798 hasConcept C119394753 @default.
- W2161871798 hasConcept C121518397 @default.
- W2161871798 hasConcept C15920480 @default.
- W2161871798 hasConcept C159985019 @default.
- W2161871798 hasConcept C171359207 @default.
- W2161871798 hasConcept C180145272 @default.
- W2161871798 hasConcept C192562407 @default.
- W2161871798 hasConcept C2779772531 @default.
- W2161871798 hasConcept C2780901341 @default.
- W2161871798 hasConcept C38052585 @default.
- W2161871798 hasConcept C521977710 @default.
- W2161871798 hasConcept C73125742 @default.
- W2161871798 hasConcept C97549433 @default.
- W2161871798 hasConcept C99595764 @default.
- W2161871798 hasConceptScore W2161871798C119394753 @default.
- W2161871798 hasConceptScore W2161871798C121518397 @default.
- W2161871798 hasConceptScore W2161871798C15920480 @default.
- W2161871798 hasConceptScore W2161871798C159985019 @default.
- W2161871798 hasConceptScore W2161871798C171359207 @default.
- W2161871798 hasConceptScore W2161871798C180145272 @default.
- W2161871798 hasConceptScore W2161871798C192562407 @default.
- W2161871798 hasConceptScore W2161871798C2779772531 @default.
- W2161871798 hasConceptScore W2161871798C2780901341 @default.
- W2161871798 hasConceptScore W2161871798C38052585 @default.
- W2161871798 hasConceptScore W2161871798C521977710 @default.
- W2161871798 hasConceptScore W2161871798C73125742 @default.
- W2161871798 hasConceptScore W2161871798C97549433 @default.
- W2161871798 hasConceptScore W2161871798C99595764 @default.
- W2161871798 hasLocation W21618717981 @default.
- W2161871798 hasOpenAccess W2161871798 @default.
- W2161871798 hasPrimaryLocation W21618717981 @default.
- W2161871798 hasRelatedWork W1968897763 @default.
- W2161871798 hasRelatedWork W1973274656 @default.
- W2161871798 hasRelatedWork W1976134454 @default.
- W2161871798 hasRelatedWork W1999252951 @default.
- W2161871798 hasRelatedWork W2014247950 @default.
- W2161871798 hasRelatedWork W2036455879 @default.
- W2161871798 hasRelatedWork W2042128499 @default.
- W2161871798 hasRelatedWork W2046459113 @default.
- W2161871798 hasRelatedWork W2056013993 @default.
- W2161871798 hasRelatedWork W2057546749 @default.
- W2161871798 hasRelatedWork W2077810080 @default.
- W2161871798 hasRelatedWork W2121207225 @default.
- W2161871798 hasRelatedWork W2167751393 @default.
- W2161871798 hasRelatedWork W2167920215 @default.
- W2161871798 hasRelatedWork W2787378453 @default.
- W2161871798 hasRelatedWork W2965004288 @default.
- W2161871798 hasRelatedWork W3048015630 @default.
- W2161871798 hasRelatedWork W959462864 @default.
- W2161871798 hasRelatedWork W3050455435 @default.
- W2161871798 hasRelatedWork W3150017054 @default.
- W2161871798 isParatext "false" @default.
- W2161871798 isRetracted "false" @default.
- W2161871798 magId "2161871798" @default.
- W2161871798 workType "article" @default.