FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W2332315216> ?p ?o ?g. }

• W2332315216 abstract "Event Abstract Back to Event Mechanical properties and microstructure of biomedical titanium alloys subjected to froction stir process Akihiro Mizutani1, Toshikazu Akahori2, Tomokazu Hattori2, Toshiaki Yasui3 and Mitsuo Niinomi4 1 Meijo University, Graduate School of Science and Technology, Japan 2 Meijo University, Faculty of Science and Technology, Japan 3 Toyohashi University of Technology, Depertment of Mechanical Engineering, Japan 4 Tohoku University, IMR, Japan Introduction: Recently, Ti-29Nb-13Ta-4.6Zr (TNTZ) with low Young’s modulus composed of alloying elements with high biocompatibility, has been developed in Japan[1]. However, as-solutionized TNTZ with the equiaxed single β phase has around twice larger Young’s modulus than that of cortical bone, and the mechanical strength is poorer than that of annealed Ti-6Al-4V ELI (Ti64). Therefore, the effect of frictional stir processing (FSP), which is one of mechanical surface modifications, under various working conditions on the microstructure and mechanical strength of nearly developed TNTZ and Ti64 as a comparison material was investigated for improvement the mechanical strength with low Young's modulus in this study. Experimental Procedures: Materials used in this study were coin-shaped TNTZ with a thickness of 3.0 mm and a diameter of 30 mm and Ti64 with a thickness of 3.0 mm and a diameter of 35 mm. The coin-shaped TNTZ were conducted with a solution treatment (ST) at 1063 K for 3.6 ks followed by water quench (WQ). Those of Ti64 were done with annealing at 978 K and 3.6 ks followed by air cooling (AC). Friction stir processing (FSP) were done on both coin-shaped samples under various working conditions such as the pressure and atmosphere. Optical microscopy (OM) and X-ray diffraction (XRD) spectroscopy were carried out on each specimen to evaluate the microstructure. Vickers hardness (HV), Young’s modulus measurement and tensile test were performed to examine the mechanical properties. Results and Discussion: Microstructure near subsurface of FPB worked surface on TNTZ shows the recrystallization area by the frictional heating with very fine equiaxed β phase with an average grain diameter of 3.0 μm as shown in Fig.1, while that of as-solutionized TNTZ was around 20 μm. The refinement ratio of microstructure is around 15%. The microstructure of Ti64, where almost all plastic flowing region was removed, showed mainly heat affected region with needle like α phase. Thus, it is considered that the heat affected region was heated over β transus more than 1000 K followed by cooling. Figure 2 shows HV of TNTZ/70.7(Air) and Ti64/6.37(Air) from FSP worked surface to around center of specimen. HV at very edge of FSP worked surface of TNTZ/70.7(Air) shows around 75% higher than that at around the center of specimen. This is attributed to fine β phase by severe deformation and frictional heating as mentioned above, and the precipitation of α phase during cooling after FSP. HV from FSP worked surface to inside of specimen shows an inclinable change with the diameter of β phase and the decrease in the amount of precipitation of α phase. On the other hand, HV in the FSP worked surface of Ti64/6.37(Air) don’t increase significantly as compared with that of TNTZ/70.7(Air). The results were attributed to the refinement of needle like α phase, the precipitation of α phase in β phase and the diffusion of gas elements such as oxygen and nitrogen. Conclusions: Surface layer of TNTZ subjected to FSP was composed of a recrystallization area and a heat affected area with a large amount of α phases in fine or relatively coarse β phases, respectively. On the other hand, that of Ti64 was occupied by mainly the heat affected area, which was composed of relatively small acicular type α/β phases in the prior β phases. Vickers hardness of TNTZ and Ti64 subjected to FSP showed the maximum value at subsurface of FSP worked surface, although the value decreased sharply as a fanction of depth from the surface. References:[1] M. Niinomi: Metall. Mater. Trans. A, 33, (2002), 477-486. Keywords: biomaterial, microstructure, Surface modification Conference: 10th World Biomaterials Congress, Montréal, Canada, 17 May - 22 May, 2016. Presentation Type: Poster Topic: Mechanical properties of biomaterials Citation: Mizutani A, Akahori T, Hattori T, Yasui T and Niinomi M (2016). Mechanical properties and microstructure of biomedical titanium alloys subjected to froction stir process. Front. Bioeng. Biotechnol. Conference Abstract: 10th World Biomaterials Congress. doi: 10.3389/conf.FBIOE.2016.01.02631 Copyright: The abstracts in this collection have not been subject to any Frontiers peer review or checks, and are not endorsed by Frontiers. They are made available through the Frontiers publishing platform as a service to conference organizers and presenters. The copyright in the individual abstracts is owned by the author of each abstract or his/her employer unless otherwise stated. Each abstract, as well as the collection of abstracts, are published under a Creative Commons CC-BY 4.0 (attribution) licence (https://creativecommons.org/licenses/by/4.0/) and may thus be reproduced, translated, adapted and be the subject of derivative works provided the authors and Frontiers are attributed. For Frontiers’ terms and conditions please see https://www.frontiersin.org/legal/terms-and-conditions. Received: 27 Mar 2016; Published Online: 30 Mar 2016. Login Required This action requires you to be registered with Frontiers and logged in. To register or login click here. Abstract Info Abstract The Authors in Frontiers Akihiro Mizutani Toshikazu Akahori Tomokazu Hattori Toshiaki Yasui Mitsuo Niinomi Google Akihiro Mizutani Toshikazu Akahori Tomokazu Hattori Toshiaki Yasui Mitsuo Niinomi Google Scholar Akihiro Mizutani Toshikazu Akahori Tomokazu Hattori Toshiaki Yasui Mitsuo Niinomi PubMed Akihiro Mizutani Toshikazu Akahori Tomokazu Hattori Toshiaki Yasui Mitsuo Niinomi Related Article in Frontiers Google Scholar PubMed Abstract Close Back to top Javascript is disabled. Please enable Javascript in your browser settings in order to see all the content on this page." @default.
• W2332315216 created "2016-06-24" @default.
• W2332315216 creator A5029961076 @default.
• W2332315216 creator A5033396074 @default.
• W2332315216 creator A5044881516 @default.
• W2332315216 creator A5081539763 @default.
• W2332315216 creator A5087759769 @default.
• W2332315216 date "2016-01-01" @default.
• W2332315216 modified "2023-10-16" @default.
• W2332315216 title "Mechanical properties and microstructure of biomedical titanium alloys subjected to froction stir process" @default.
• W2332315216 doi "https://doi.org/10.3389/conf.fbioe.2016.01.02631" @default.
• W2332315216 hasPublicationYear "2016" @default.
• W2332315216 type Work @default.
• W2332315216 sameAs 2332315216 @default.
• W2332315216 citedByCount "0" @default.
• W2332315216 crossrefType "journal-article" @default.
• W2332315216 hasAuthorship W2332315216A5029961076 @default.
• W2332315216 hasAuthorship W2332315216A5033396074 @default.
• W2332315216 hasAuthorship W2332315216A5044881516 @default.
• W2332315216 hasAuthorship W2332315216A5081539763 @default.
• W2332315216 hasAuthorship W2332315216A5087759769 @default.
• W2332315216 hasBestOaLocation W23323152161 @default.
• W2332315216 hasConcept C159985019 @default.
• W2332315216 hasConcept C191897082 @default.
• W2332315216 hasConcept C192562407 @default.
• W2332315216 hasConcept C193867417 @default.
• W2332315216 hasConcept C2777230088 @default.
• W2332315216 hasConcept C2777855556 @default.
• W2332315216 hasConcept C2780026712 @default.
• W2332315216 hasConcept C506065880 @default.
• W2332315216 hasConcept C81710450 @default.
• W2332315216 hasConcept C87976508 @default.
• W2332315216 hasConcept C8953137 @default.
• W2332315216 hasConceptScore W2332315216C159985019 @default.
• W2332315216 hasConceptScore W2332315216C191897082 @default.
• W2332315216 hasConceptScore W2332315216C192562407 @default.
• W2332315216 hasConceptScore W2332315216C193867417 @default.
• W2332315216 hasConceptScore W2332315216C2777230088 @default.
• W2332315216 hasConceptScore W2332315216C2777855556 @default.
• W2332315216 hasConceptScore W2332315216C2780026712 @default.
• W2332315216 hasConceptScore W2332315216C506065880 @default.
• W2332315216 hasConceptScore W2332315216C81710450 @default.
• W2332315216 hasConceptScore W2332315216C87976508 @default.
• W2332315216 hasConceptScore W2332315216C8953137 @default.
• W2332315216 hasLocation W23323152161 @default.
• W2332315216 hasOpenAccess W2332315216 @default.
• W2332315216 hasPrimaryLocation W23323152161 @default.
• W2332315216 hasRelatedWork W1570910991 @default.
• W2332315216 hasRelatedWork W2058945371 @default.
• W2332315216 hasRelatedWork W2074735591 @default.
• W2332315216 hasRelatedWork W2367294898 @default.
• W2332315216 hasRelatedWork W2372585231 @default.
• W2332315216 hasRelatedWork W2780796883 @default.
• W2332315216 hasRelatedWork W2944847224 @default.
• W2332315216 hasRelatedWork W2980884952 @default.
• W2332315216 hasRelatedWork W3037536156 @default.
• W2332315216 hasRelatedWork W3046190049 @default.
• W2332315216 hasVolume "4" @default.
• W2332315216 isParatext "false" @default.
• W2332315216 isRetracted "false" @default.
• W2332315216 magId "2332315216" @default.
• W2332315216 workType "article" @default.