Matches in SemOpenAlex for { <https://semopenalex.org/work/W2897865601> ?p ?o ?g. }
Showing items 1 to 72 of
72
with 100 items per page.
- W2897865601 endingPage "688" @default.
- W2897865601 startingPage "683" @default.
- W2897865601 abstract "The problem of determining the maximum diameter of working rolls is typical for screw rolling mills that have more than two working rolls. Precise determination of the working roll diameter is especially important for three-roll mills, which are widely used in such industries as rolling and calibration, and radial-shear rolling mills operating at large feeding and rolling angles. Typically, the diameter of working rolls is determined in a constructive way or using 3D modeling. These methods are quite complex, require special skills, and do not allow investigation of the influence of main tuning mill factors such as feeding and rolling angles. There is a calculated method for determining the diameter of the roll barrel for a three-roll mill, but it is applicable for mills working at feeding angles of up to 10 degrees and rolling angles of 4 – 7 degrees. In conditions of radial-shear rolling, this method is not used, since it does not take into account the influence of feeding and rolling angles on which the conditions of the deformation process, manufacturability and quality of the products depend. The article considers a more general method for determining the diameter of working rolls of three or more rolling mills, taking into account their rotation at the feeding and rolling angles. The relationship between diameter of the rolls, their number, minimum diameter of the deformation center, the feeding and rolling angles are shown, which makes it possible to evaluate the structural capabilities of both three and four-roll rolling mills. The results of the presented work make it possible to expand the possibilities for further studies of the technology and equipment of three-roll screw rolling mills for the production of solid and hollow products using completely new deformation modes for the processes of rolling out hollow products of their reduction as well as radial shearing rolling. Importantly, it is possible to supplement existing knowledge about the change in geometry of deformation center, and also to predict geometric parameters of the working rolls of the projected multi-roll mills for given rolled products sizes." @default.
- W2897865601 created "2018-10-26" @default.
- W2897865601 creator A5011171663 @default.
- W2897865601 creator A5034757620 @default.
- W2897865601 creator A5039700471 @default.
- W2897865601 date "2018-10-21" @default.
- W2897865601 modified "2023-09-27" @default.
- W2897865601 title "Determination of rolls diameter for screw-rolling mills" @default.
- W2897865601 cites W1971599363 @default.
- W2897865601 cites W2006368993 @default.
- W2897865601 cites W2008247510 @default.
- W2897865601 doi "https://doi.org/10.17073/0368-0797-2019-9-683-688" @default.
- W2897865601 hasPublicationYear "2018" @default.
- W2897865601 type Work @default.
- W2897865601 sameAs 2897865601 @default.
- W2897865601 citedByCount "2" @default.
- W2897865601 countsByYear W28978656012020 @default.
- W2897865601 countsByYear W28978656012021 @default.
- W2897865601 crossrefType "journal-article" @default.
- W2897865601 hasAuthorship W2897865601A5011171663 @default.
- W2897865601 hasAuthorship W2897865601A5034757620 @default.
- W2897865601 hasAuthorship W2897865601A5039700471 @default.
- W2897865601 hasBestOaLocation W28978656011 @default.
- W2897865601 hasConcept C111919701 @default.
- W2897865601 hasConcept C127413603 @default.
- W2897865601 hasConcept C159985019 @default.
- W2897865601 hasConcept C16057445 @default.
- W2897865601 hasConcept C192562407 @default.
- W2897865601 hasConcept C204366326 @default.
- W2897865601 hasConcept C2524010 @default.
- W2897865601 hasConcept C2985318046 @default.
- W2897865601 hasConcept C33923547 @default.
- W2897865601 hasConcept C41008148 @default.
- W2897865601 hasConcept C74050887 @default.
- W2897865601 hasConcept C77624028 @default.
- W2897865601 hasConcept C78519656 @default.
- W2897865601 hasConcept C98045186 @default.
- W2897865601 hasConceptScore W2897865601C111919701 @default.
- W2897865601 hasConceptScore W2897865601C127413603 @default.
- W2897865601 hasConceptScore W2897865601C159985019 @default.
- W2897865601 hasConceptScore W2897865601C16057445 @default.
- W2897865601 hasConceptScore W2897865601C192562407 @default.
- W2897865601 hasConceptScore W2897865601C204366326 @default.
- W2897865601 hasConceptScore W2897865601C2524010 @default.
- W2897865601 hasConceptScore W2897865601C2985318046 @default.
- W2897865601 hasConceptScore W2897865601C33923547 @default.
- W2897865601 hasConceptScore W2897865601C41008148 @default.
- W2897865601 hasConceptScore W2897865601C74050887 @default.
- W2897865601 hasConceptScore W2897865601C77624028 @default.
- W2897865601 hasConceptScore W2897865601C78519656 @default.
- W2897865601 hasConceptScore W2897865601C98045186 @default.
- W2897865601 hasIssue "9" @default.
- W2897865601 hasLocation W28978656011 @default.
- W2897865601 hasOpenAccess W2897865601 @default.
- W2897865601 hasPrimaryLocation W28978656011 @default.
- W2897865601 hasRelatedWork W2061026800 @default.
- W2897865601 hasRelatedWork W2352991995 @default.
- W2897865601 hasRelatedWork W2356873474 @default.
- W2897865601 hasRelatedWork W2357876304 @default.
- W2897865601 hasRelatedWork W2366657186 @default.
- W2897865601 hasRelatedWork W2370097867 @default.
- W2897865601 hasRelatedWork W2372484039 @default.
- W2897865601 hasRelatedWork W2383368692 @default.
- W2897865601 hasRelatedWork W2383810034 @default.
- W2897865601 hasRelatedWork W2978437175 @default.
- W2897865601 hasVolume "61" @default.
- W2897865601 isParatext "false" @default.
- W2897865601 isRetracted "false" @default.
- W2897865601 magId "2897865601" @default.
- W2897865601 workType "article" @default.