FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W302983002> ?p ?o ?g. }

• W302983002 abstract "Design verification tests were performed on samples representing the aerobrake of the Mars/Pathfinder vehicle. The test specimens consisted of the SLA-561V ablator bonded to the honeycomb structure. The primary objective was to evaluate the ablation materials performance and to measure temperatures within the ablator, at the structural bondline and at the back sheet of the honeycomb structure. Other objectives were to evaluate the effect of ablative repair plug material treatment and voids in the heat shield. A total of 29 models were provided for testing in the Ames 60MW arc-jet facility. Of these, 23 models were flat-faced and six remaining models were curved edge ones, intended to simulate the conditions on the curved rim of the forebody where the maximum shear occurred. Eight sets of test conditions were used. The stagnation point heating rates varied from 47 to 240 W/cm2 and the stagnation pressures from 0.15 to 0.27 atm. (The maximum flight values are 132 W/cm2 and 0.25 atm) The majority of these runs were made at a nominal stagnation pressure of 0.25 atm. Two higher pressure runs were made to check the current (denser) ablation material for spallation, or other forms of thermal stress failure. Over 60% of the flatfaced models yielded good thermocouple data and all produced useful surface recession information. Of the five curved-edge models that were tested, only one gave good data; the remaining ones experienced model-holder failure. The test results can be summarized by noting that no failure of the ablative material was observed on any model. Also, the bondline temperature design limit of 250 C was never reached within an equivalent flight time despite a stagnation point heat load that exceeded the maximum flight value by up to 130%. At heating rates of over 200W/cm2 and stagnation pressures of 0.25 atm, or greater, the average surface recessions exceeded 0.5 cm on some models. The surface roughness increased dramatically at pressures above 0.25 atm and was four times greater at 0.27 atm than at 0.25 atm. Procured repair plug material performed much better than room-temperature cured plugs, as observed in the previous tests. Voids in the ablator did not increase local temperatures and gaps did not grow during testing." @default.
• W302983002 created "2016-06-24" @default.
• W302983002 creator A5001621466 @default.
• W302983002 creator A5006515904 @default.
• W302983002 creator A5022895849 @default.
• W302983002 creator A5038964286 @default.
• W302983002 creator A5040506193 @default.
• W302983002 creator A5063306631 @default.
• W302983002 creator A5076523755 @default.
• W302983002 creator A5064296982 @default.
• W302983002 date "1995-01-01" @default.
• W302983002 modified "2023-09-23" @default.
• W302983002 title "Ames Research Center Mars/Pathfinder Heat Shield Design Verification ARC-JET Test" @default.
• W302983002 hasPublicationYear "1995" @default.
• W302983002 type Work @default.
• W302983002 sameAs 302983002 @default.
• W302983002 citedByCount "0" @default.
• W302983002 crossrefType "journal-article" @default.
• W302983002 hasAuthorship W302983002A5001621466 @default.
• W302983002 hasAuthorship W302983002A5006515904 @default.
• W302983002 hasAuthorship W302983002A5022895849 @default.
• W302983002 hasAuthorship W302983002A5038964286 @default.
• W302983002 hasAuthorship W302983002A5040506193 @default.
• W302983002 hasAuthorship W302983002A5063306631 @default.
• W302983002 hasAuthorship W302983002A5064296982 @default.
• W302983002 hasAuthorship W302983002A5076523755 @default.
• W302983002 hasConcept C117954924 @default.
• W302983002 hasConcept C121332964 @default.
• W302983002 hasConcept C127413603 @default.
• W302983002 hasConcept C1276947 @default.
• W302983002 hasConcept C159985019 @default.
• W302983002 hasConcept C192562407 @default.
• W302983002 hasConcept C2986597240 @default.
• W302983002 hasConcept C50517652 @default.
• W302983002 hasConcept C57879066 @default.
• W302983002 hasConcept C66938386 @default.
• W302983002 hasConcept C83260615 @default.
• W302983002 hasConcept C9715774 @default.
• W302983002 hasConcept C9761082 @default.
• W302983002 hasConceptScore W302983002C117954924 @default.
• W302983002 hasConceptScore W302983002C121332964 @default.
• W302983002 hasConceptScore W302983002C127413603 @default.
• W302983002 hasConceptScore W302983002C1276947 @default.
• W302983002 hasConceptScore W302983002C159985019 @default.
• W302983002 hasConceptScore W302983002C192562407 @default.
• W302983002 hasConceptScore W302983002C2986597240 @default.
• W302983002 hasConceptScore W302983002C50517652 @default.
• W302983002 hasConceptScore W302983002C57879066 @default.
• W302983002 hasConceptScore W302983002C66938386 @default.
• W302983002 hasConceptScore W302983002C83260615 @default.
• W302983002 hasConceptScore W302983002C9715774 @default.
• W302983002 hasConceptScore W302983002C9761082 @default.
• W302983002 hasOpenAccess W302983002 @default.
• W302983002 hasRelatedWork W103772975 @default.
• W302983002 hasRelatedWork W1536613292 @default.
• W302983002 hasRelatedWork W1552736041 @default.
• W302983002 hasRelatedWork W1972778212 @default.
• W302983002 hasRelatedWork W2035882393 @default.
• W302983002 hasRelatedWork W2312204181 @default.
• W302983002 hasRelatedWork W2312442425 @default.
• W302983002 hasRelatedWork W2316090706 @default.
• W302983002 hasRelatedWork W2316545605 @default.
• W302983002 hasRelatedWork W2316933843 @default.
• W302983002 hasRelatedWork W2379076598 @default.
• W302983002 hasRelatedWork W2569116383 @default.
• W302983002 hasRelatedWork W2774644217 @default.
• W302983002 hasRelatedWork W2891375609 @default.
• W302983002 hasRelatedWork W2965988231 @default.
• W302983002 hasRelatedWork W298691222 @default.
• W302983002 hasRelatedWork W770062075 @default.
• W302983002 hasRelatedWork W794561729 @default.
• W302983002 hasRelatedWork W831767113 @default.
• W302983002 hasRelatedWork W212550402 @default.
• W302983002 isParatext "false" @default.
• W302983002 isRetracted "false" @default.
• W302983002 magId "302983002" @default.
• W302983002 workType "article" @default.