Matches in SemOpenAlex for { <https://semopenalex.org/work/W3045714314> ?p ?o ?g. }
Showing items 1 to 94 of
94
with 100 items per page.
- W3045714314 endingPage "786" @default.
- W3045714314 startingPage "768" @default.
- W3045714314 abstract "Abstract Due to its vast benefits, Additive Manufacturing (AM) has attracted a great deal of attention during the last two decades. Selective Laser Melting (SLM) is one of the most increasingly used AM techniques in the world. The machinability of SLM-manufactured Ti6Al4V parts in as-built (SLM-AB) and stress-relief (SLM-SR) conditions was studied in this work via toroidal milling. A conventional processed Ti6Al4V alloy was tested as a reference. SLM process parameters for producing near fully dense parts were optimized to yield a volumetric energy density of 46.4 J/mm3. Relative density, microstructure, hardness, residual stresses, surface roughness, cutting forces, tool wear, and chip morphology were evaluated. The SLM-manufactured parts gave a relative density of 99.70 % and higher hardness values than those of the conventional parts by a factor of about 1.2. The conventional, SLM-AB, and SLM-SR Ti6Al4V alloys exhibited microstructures consisting of α and β phases, acicular α′ martensite, α′ martensite and some amounts of α + β phases, respectively. The conventional alloy had the lowest residual stress. SLM-AB had considerable residual tensile stress in the 0° direction of measurement, whereas SLM-SR had the highest compressive stress in both 0° and 90° directions. The lowest cutting force was observed in the conventional alloy and the highest in the SLM-SR alloy. The SLM-AB alloy featured the highest flank wear. However, no significant difference in flank wear was observed in the conventional and SLM-SR alloys." @default.
- W3045714314 created "2020-08-03" @default.
- W3045714314 creator A5007111458 @default.
- W3045714314 creator A5019961952 @default.
- W3045714314 creator A5059916759 @default.
- W3045714314 creator A5080824832 @default.
- W3045714314 creator A5091776265 @default.
- W3045714314 date "2020-09-01" @default.
- W3045714314 modified "2023-10-16" @default.
- W3045714314 title "Machinability of SLM-produced Ti6Al4V titanium alloy parts" @default.
- W3045714314 cites W1973709573 @default.
- W3045714314 cites W1982728817 @default.
- W3045714314 cites W1997996304 @default.
- W3045714314 cites W2004265799 @default.
- W3045714314 cites W2012336197 @default.
- W3045714314 cites W2023758491 @default.
- W3045714314 cites W2028144650 @default.
- W3045714314 cites W2031235577 @default.
- W3045714314 cites W2042310099 @default.
- W3045714314 cites W2044004898 @default.
- W3045714314 cites W2049039109 @default.
- W3045714314 cites W2049993169 @default.
- W3045714314 cites W2072455331 @default.
- W3045714314 cites W2091242520 @default.
- W3045714314 cites W2100555050 @default.
- W3045714314 cites W2424885551 @default.
- W3045714314 cites W2464910155 @default.
- W3045714314 cites W2466590797 @default.
- W3045714314 cites W2469792432 @default.
- W3045714314 cites W2744431515 @default.
- W3045714314 cites W2762993258 @default.
- W3045714314 cites W2771072344 @default.
- W3045714314 cites W2791687599 @default.
- W3045714314 cites W2792453761 @default.
- W3045714314 cites W2809577129 @default.
- W3045714314 cites W2890904339 @default.
- W3045714314 cites W2903980596 @default.
- W3045714314 cites W2904619063 @default.
- W3045714314 cites W2917515729 @default.
- W3045714314 cites W2927563491 @default.
- W3045714314 cites W2932599327 @default.
- W3045714314 cites W2973769717 @default.
- W3045714314 cites W316616532 @default.
- W3045714314 doi "https://doi.org/10.1016/j.jmapro.2020.07.035" @default.
- W3045714314 hasPublicationYear "2020" @default.
- W3045714314 type Work @default.
- W3045714314 sameAs 3045714314 @default.
- W3045714314 citedByCount "57" @default.
- W3045714314 countsByYear W30457143142020 @default.
- W3045714314 countsByYear W30457143142021 @default.
- W3045714314 countsByYear W30457143142022 @default.
- W3045714314 countsByYear W30457143142023 @default.
- W3045714314 crossrefType "journal-article" @default.
- W3045714314 hasAuthorship W3045714314A5007111458 @default.
- W3045714314 hasAuthorship W3045714314A5019961952 @default.
- W3045714314 hasAuthorship W3045714314A5059916759 @default.
- W3045714314 hasAuthorship W3045714314A5080824832 @default.
- W3045714314 hasAuthorship W3045714314A5091776265 @default.
- W3045714314 hasConcept C159985019 @default.
- W3045714314 hasConcept C191897082 @default.
- W3045714314 hasConcept C192562407 @default.
- W3045714314 hasConcept C2775926494 @default.
- W3045714314 hasConcept C2780026712 @default.
- W3045714314 hasConcept C506065880 @default.
- W3045714314 hasConcept C523214423 @default.
- W3045714314 hasConcept C8953137 @default.
- W3045714314 hasConceptScore W3045714314C159985019 @default.
- W3045714314 hasConceptScore W3045714314C191897082 @default.
- W3045714314 hasConceptScore W3045714314C192562407 @default.
- W3045714314 hasConceptScore W3045714314C2775926494 @default.
- W3045714314 hasConceptScore W3045714314C2780026712 @default.
- W3045714314 hasConceptScore W3045714314C506065880 @default.
- W3045714314 hasConceptScore W3045714314C523214423 @default.
- W3045714314 hasConceptScore W3045714314C8953137 @default.
- W3045714314 hasLocation W30457143141 @default.
- W3045714314 hasOpenAccess W3045714314 @default.
- W3045714314 hasPrimaryLocation W30457143141 @default.
- W3045714314 hasRelatedWork W1907791393 @default.
- W3045714314 hasRelatedWork W1998029461 @default.
- W3045714314 hasRelatedWork W1999962534 @default.
- W3045714314 hasRelatedWork W2035401059 @default.
- W3045714314 hasRelatedWork W2046996426 @default.
- W3045714314 hasRelatedWork W217893180 @default.
- W3045714314 hasRelatedWork W2349107874 @default.
- W3045714314 hasRelatedWork W2372585231 @default.
- W3045714314 hasRelatedWork W2386135830 @default.
- W3045714314 hasRelatedWork W3093124064 @default.
- W3045714314 hasVolume "57" @default.
- W3045714314 isParatext "false" @default.
- W3045714314 isRetracted "false" @default.
- W3045714314 magId "3045714314" @default.
- W3045714314 workType "article" @default.