Matches in SemOpenAlex for { <https://semopenalex.org/work/W3112196853> ?p ?o ?g. }
Showing items 1 to 68 of
68
with 100 items per page.
- W3112196853 abstract "In the hot forging process, an abrasive wear is a major problem in the manufacturing process which may possibly happen together with the plastic deformation. Both effects are difficult to distinguish in the real tooling. Finite Element Modeling (FEM) is a tool that use to simulate those phenomena in the hot forging process. However, some unknown factors are not directly obtained from the actual measurement. Thus, the sensitivity analysis is applied together with FEM to approximate those parameters. This research was to evaluate the die defects of the hot forged axle shaft process which were the plastic deformation and the abrasive wear. The reliable simulation modeling was developed by conducting the sensitivity analysis of the unknown parameters; heat transfer and friction coefficient, and compared the results with the experimental results. Then, the evaluation of the defects was performed by considering the effect of the plastic deformation and abrasive wear separately. The plastic deformation would be determined by comparing the effective stress with the yield strength of the die material at the same temperature. To predict abrasive wear in 3D space the die profile from the actual process was measured by CMM and then it was compared with that obtained by FEM. Archard’s model was used to predict the abrasive die wear in FEM. The variation of the K-values was significant to the wear prediction. According to this study, the average K-value obtained from different positions gives the best representative than considering only a single point K-value." @default.
- W3112196853 created "2020-12-21" @default.
- W3112196853 creator A5014942895 @default.
- W3112196853 creator A5071646452 @default.
- W3112196853 creator A5079880437 @default.
- W3112196853 date "2020-12-08" @default.
- W3112196853 modified "2023-09-25" @default.
- W3112196853 title "Evaluation of Forging Die Defect by Considering Plastic Deformation and Abrasive Wear in a Hot Forged Axle Shaft" @default.
- W3112196853 cites W2058455157 @default.
- W3112196853 doi "https://doi.org/10.14416/j.asep.2020.12.005" @default.
- W3112196853 hasPublicationYear "2020" @default.
- W3112196853 type Work @default.
- W3112196853 sameAs 3112196853 @default.
- W3112196853 citedByCount "1" @default.
- W3112196853 countsByYear W31121968532021 @default.
- W3112196853 crossrefType "journal-article" @default.
- W3112196853 hasAuthorship W3112196853A5014942895 @default.
- W3112196853 hasAuthorship W3112196853A5071646452 @default.
- W3112196853 hasAuthorship W3112196853A5079880437 @default.
- W3112196853 hasConcept C111106434 @default.
- W3112196853 hasConcept C127413603 @default.
- W3112196853 hasConcept C129727815 @default.
- W3112196853 hasConcept C135628077 @default.
- W3112196853 hasConcept C159985019 @default.
- W3112196853 hasConcept C171250308 @default.
- W3112196853 hasConcept C191897082 @default.
- W3112196853 hasConcept C192562407 @default.
- W3112196853 hasConcept C204366326 @default.
- W3112196853 hasConcept C21200559 @default.
- W3112196853 hasConcept C24326235 @default.
- W3112196853 hasConcept C2780957350 @default.
- W3112196853 hasConcept C66938386 @default.
- W3112196853 hasConcept C78519656 @default.
- W3112196853 hasConcept C96494537 @default.
- W3112196853 hasConceptScore W3112196853C111106434 @default.
- W3112196853 hasConceptScore W3112196853C127413603 @default.
- W3112196853 hasConceptScore W3112196853C129727815 @default.
- W3112196853 hasConceptScore W3112196853C135628077 @default.
- W3112196853 hasConceptScore W3112196853C159985019 @default.
- W3112196853 hasConceptScore W3112196853C171250308 @default.
- W3112196853 hasConceptScore W3112196853C191897082 @default.
- W3112196853 hasConceptScore W3112196853C192562407 @default.
- W3112196853 hasConceptScore W3112196853C204366326 @default.
- W3112196853 hasConceptScore W3112196853C21200559 @default.
- W3112196853 hasConceptScore W3112196853C24326235 @default.
- W3112196853 hasConceptScore W3112196853C2780957350 @default.
- W3112196853 hasConceptScore W3112196853C66938386 @default.
- W3112196853 hasConceptScore W3112196853C78519656 @default.
- W3112196853 hasConceptScore W3112196853C96494537 @default.
- W3112196853 hasIssue "1" @default.
- W3112196853 hasLocation W31121968531 @default.
- W3112196853 hasOpenAccess W3112196853 @default.
- W3112196853 hasPrimaryLocation W31121968531 @default.
- W3112196853 hasRelatedWork W2248418976 @default.
- W3112196853 hasRelatedWork W2348419206 @default.
- W3112196853 hasRelatedWork W2350818105 @default.
- W3112196853 hasRelatedWork W2370180985 @default.
- W3112196853 hasRelatedWork W2374691405 @default.
- W3112196853 hasRelatedWork W2375486894 @default.
- W3112196853 hasRelatedWork W2381451407 @default.
- W3112196853 hasRelatedWork W3011128213 @default.
- W3112196853 hasRelatedWork W3112196853 @default.
- W3112196853 hasRelatedWork W4310180239 @default.
- W3112196853 hasVolume "14" @default.
- W3112196853 isParatext "false" @default.
- W3112196853 isRetracted "false" @default.
- W3112196853 magId "3112196853" @default.
- W3112196853 workType "article" @default.