FRINK Linked Data Fragments server

Matches in SemOpenAlex for { <https://semopenalex.org/work/W3135835991> ?p ?o ?g. }

• W3135835991 endingPage "7814" @default.
• W3135835991 startingPage "7803" @default.
• W3135835991 abstract "This paper presents a Finite Element Analysis (FEA) simulation study conducted on ball endmill for fixed 3 + 1 and 3 + 2 axis orientations for machining Ti-6Al-4 V. This work adopts a tungsten carbide (WC) Ø18.6 mm diametrical/6fluted ball endmill to analyse maximum principal elastic strain (εmax-max-principal-elastic), maximum principal stress (σmax-principal) along with cutting tools forces in the axial (Fz), radial (Fy), tangential (Fx) and total (Ftotal) directions. The machining orientations considered for 3 + 1 and 3 + 2 axis are (i) tilt angles of 5°, 10°, 15° & 20° and (ii) lead angles of 5°, 10° & 15° with a constant fixed tilt angle of 10°. The cutting speed and feed rate per tooth is taken as 450 m/min and 0.5 mm/tooth. These are based on a high speed machining (HSM) scenario and has been dynamically simulated for a maximum of 175,000 cycles. From the simulation study considered at 16–20 valid cutting points, it can be noticed that in 3 + 1 axis, for a tilt angle of 10° and 3 + 2 axis for a Tilt 10°/Lead 10° the σmax-principal and εmax-max-principal-elastic are higher when compared with all tilt/lead angles. In case of total forces (Ftotal) from all 3 directions (Fx, Fy and Fz) not much variation can be noticed for different tilt/lead angles, but higher values are recorded with 3 + 1 axis at 5° tilt angle and 3 + 2 axis at tilt/lead angle of 10°. The paper provides a critical comparative study on the 3 + 1/ 3 + 2 axis orientations highlighting the cutting strain/stress with tool forces at valid cutting points considering entry, middle and exit region of the blank by emphasizing the importance of cutting tool design parameters." @default.
• W3135835991 created "2021-03-15" @default.
• W3135835991 creator A5007443429 @default.
• W3135835991 creator A5074134535 @default.
• W3135835991 creator A5083727238 @default.
• W3135835991 date "2021-01-01" @default.
• W3135835991 modified "2023-09-27" @default.
• W3135835991 title "A FEA simulation study of ball end mill for fixed 3+1 / 3+2 axis machining of Ti-6Al-4V" @default.
• W3135835991 cites W1968720824 @default.
• W3135835991 cites W1970144651 @default.
• W3135835991 cites W1979988544 @default.
• W3135835991 cites W1987170375 @default.
• W3135835991 cites W1999468163 @default.
• W3135835991 cites W2006705286 @default.
• W3135835991 cites W2018166358 @default.
• W3135835991 cites W2026041204 @default.
• W3135835991 cites W2030355037 @default.
• W3135835991 cites W2049977749 @default.
• W3135835991 cites W2060781469 @default.
• W3135835991 cites W2062257465 @default.
• W3135835991 cites W2070792579 @default.
• W3135835991 cites W2074732490 @default.
• W3135835991 cites W2092425525 @default.
• W3135835991 cites W2804804101 @default.
• W3135835991 cites W2891387304 @default.
• W3135835991 cites W2995509321 @default.
• W3135835991 cites W3020867389 @default.
• W3135835991 doi "https://doi.org/10.1016/j.matpr.2021.02.369" @default.
• W3135835991 hasPublicationYear "2021" @default.
• W3135835991 type Work @default.
• W3135835991 sameAs 3135835991 @default.
• W3135835991 citedByCount "1" @default.
• W3135835991 countsByYear W31358359912023 @default.
• W3135835991 crossrefType "journal-article" @default.
• W3135835991 hasAuthorship W3135835991A5007443429 @default.
• W3135835991 hasAuthorship W3135835991A5074134535 @default.
• W3135835991 hasAuthorship W3135835991A5083727238 @default.
• W3135835991 hasBestOaLocation W31358359912 @default.
• W3135835991 hasConcept C122041747 @default.
• W3135835991 hasConcept C127413603 @default.
• W3135835991 hasConcept C135628077 @default.
• W3135835991 hasConcept C159985019 @default.
• W3135835991 hasConcept C161326058 @default.
• W3135835991 hasConcept C191897082 @default.
• W3135835991 hasConcept C192562407 @default.
• W3135835991 hasConcept C2524010 @default.
• W3135835991 hasConcept C2779844322 @default.
• W3135835991 hasConcept C2779952096 @default.
• W3135835991 hasConcept C2781422231 @default.
• W3135835991 hasConcept C33923547 @default.
• W3135835991 hasConcept C523214423 @default.
• W3135835991 hasConcept C66938386 @default.
• W3135835991 hasConceptScore W3135835991C122041747 @default.
• W3135835991 hasConceptScore W3135835991C127413603 @default.
• W3135835991 hasConceptScore W3135835991C135628077 @default.
• W3135835991 hasConceptScore W3135835991C159985019 @default.
• W3135835991 hasConceptScore W3135835991C161326058 @default.
• W3135835991 hasConceptScore W3135835991C191897082 @default.
• W3135835991 hasConceptScore W3135835991C192562407 @default.
• W3135835991 hasConceptScore W3135835991C2524010 @default.
• W3135835991 hasConceptScore W3135835991C2779844322 @default.
• W3135835991 hasConceptScore W3135835991C2779952096 @default.
• W3135835991 hasConceptScore W3135835991C2781422231 @default.
• W3135835991 hasConceptScore W3135835991C33923547 @default.
• W3135835991 hasConceptScore W3135835991C523214423 @default.
• W3135835991 hasConceptScore W3135835991C66938386 @default.
• W3135835991 hasLocation W31358359911 @default.
• W3135835991 hasLocation W31358359912 @default.
• W3135835991 hasLocation W31358359913 @default.
• W3135835991 hasOpenAccess W3135835991 @default.
• W3135835991 hasPrimaryLocation W31358359911 @default.
• W3135835991 hasRelatedWork W104135509 @default.
• W3135835991 hasRelatedWork W2030949112 @default.
• W3135835991 hasRelatedWork W2038647073 @default.
• W3135835991 hasRelatedWork W2078161611 @default.
• W3135835991 hasRelatedWork W2320830476 @default.
• W3135835991 hasRelatedWork W2378138008 @default.
• W3135835991 hasRelatedWork W2627040273 @default.
• W3135835991 hasRelatedWork W2745236017 @default.
• W3135835991 hasRelatedWork W3135835991 @default.
• W3135835991 hasRelatedWork W4249829372 @default.
• W3135835991 hasVolume "46" @default.
• W3135835991 isParatext "false" @default.
• W3135835991 isRetracted "false" @default.
• W3135835991 magId "3135835991" @default.
• W3135835991 workType "article" @default.